Polímeros: Ciência e Tecnologia
https://app.periodikos.com.br/journal/polimeros/article/doi/10.1590/S0104-14282002000200006
Polímeros: Ciência e Tecnologia
Scientific & Technical Article

Polietileno de Alta Densidade Tenacificado com Elastômero Metalocênico: 1. Propriedades Mecânicas e Características Morfológicas

Rubber Toughened High Density Polyethylene: 1. Mechanical Properties and Morphological Characteristics

Guimarães, Maria José O. C.; Rocha, Marisa C. G.; Coutinho, Fernanda M. B.

Downloads: 0
Views: 1170

Resumo

Neste trabalho foram estudadas as propriedades mecânicas e morfológicas de polietileno de alta densidade (HDPE) tenacificado com dois tipos de elastômeros metalocênicos à base de etileno/1- octeno (EOC). Esses elastômeros são polímeros comerciais com diferenças quanto ao peso molecular, índice de fluidez e índice Dow de reologia (DRI). Misturas físicas de HDPE e EOC foram processadas em extrusora monorosca Wortex (L/D=32), à 230°C e 50 rpm, utilizando percentagem mássica do EOC de 5% a 80%. Foi observado um efeito sinergístico nas propriedades tênseis e características de supertenacificação para materiais contendo proporções do EOC maiores do que 5%. Cavitação, deformação plástica e cavitação fibrilada foram observados nos processos de deformação. Materiais contendo até 50% do EOC apresentaram morfologias dispersas com domínios elastoméricos esféricos, distribuídos uniformemente e com tamanho médio de partícula na faixa de 0,30 a 0,45 μm. A tenacificação de HDPE com os elastômeros etilênicos produziu materiais com boas propriedades e compatibilização tecnológica devido à existência de baixa tensão interfacial entre esses polímeros.

Palavras-chave

HDPE, elastômeros metalocênicos, tenacificação, morfologia

Abstract

The mechanical and morphological properties of high density polyethylene (HDPE) toughened with two different grades of metallocene elastomers based on ethylene/1- octene (EOC) were studied. These elastomers were commercial polymers differing in molecular weight, melt flow index and Dow rheology index (DRI). Blends were processed in a Wortex single screw extruder (L/D=32), at 230°C and 50 rpm, using mass fraction weight percent of EOC in the range from 5% to 80%. A synergistic effect on the tensile properties and supertough behavior for blends with EOC concentrations higher than 5% was observed. Cavitation, plastic deformation and fibrillized cavitation were observed in the deformation processes. Materials containing up to 50% of EOC exhibited dispersed morphologies with EOC spherical domains uniformly distributed with particle size in the range from 0.30 to 0.45 μm. The toughening of HDPE with ethylenic elastomers produced materials with good properties and technological compatibilization.

Keywords

HDPE, metallocene elastomers, toughening, morphology

References



1. Bari, D. F. - Impact of Technology on Global Polyethylene in Materials, Properties, Processing & Markets, Design Library, New York (1998).

2. Ferro, S. - Plástico Moderno, nº 304, 16 (1999).

3. Montaga, A. A. - Chemitech, 25, 44 (1995).

4. Montaga, A. A. - Hydrocarbon Processing, 57 (1994).

5. Tung, j. F.; Liew, K. F. - Proceedings of SPE ANTEC-95, 962 (1995).

6. Silva, A. L. N.; Rocha, M. C. G.; Coutinho, F. M. B.; Bretas, R.; Scuracchio, C. -, J. Appl. Polym. Sci., 75, 692 (2002).

7. Guimarães, M. J. O. C.; Coutinho, F. M. B.; Rocha, M. C. G.; Garcia, M. E. F. - J. Appl. Polym. Sci., 81, 1991 (2001).

8. Kitao, K. - Polym. Eng. Sci., 37, 777 (1997).

9. Barteczak, Z.; Argon, A. S.; Cohen, R. E.; Weinberg, M. - Polymer, 40, 2331 (1999).

10. Jiang, W.; An, L.; Jiang, B. - Polymer, 42, 4777 (2001).

11. Lotti, C.; Correa, C. A.; Canevarolo, S. V. - Mat. Res., 3, 37 (2000).

12. Kim, G. M.; Michler, G. H.; Gahleitner, M.; Mülhaup, R. - Polym. Adv. Techn., 9, 709 (1998).

13. Liung, H.; Jiang, W.; Zhang, J.; Jiang, B. - J. Appl. Polym. Sci., 59, 505 (1996).

14. Moore, E. P. - Principles of rubber toughening in Polypropylene Handbook, Hanser Publishers, New York, (1996).

15. Cho, K.; Yang, J.; Park, C. E. - Polymer, 39, 3073 (1998).

16. Li, W. D.; Li, R. K. Y.; Tyjong, S. C. - Polym. Test, 16, 563 (1997).

17. Van der Wal, A.; Gaymans, R. J. - Polymer, 40, 6045 (1999).

18. Van der Wal, A.; Verheul, A. J. J.; Gaymans, R. J. - Polymer, 40, 6057 (1999).

19. Wu, S. - J. Appl. Polym. Sci., 35, 549 (1988).

20. Gugumus, F.; Lelli, N. - Polym. Degrad. Stab., 72, 407 (2001).

21. Shishesag, M. R.; Donatelli, A. A. - Polym. Eng. Sci., 21, 869 (1981).

22. Yousefi, A. A.; Ait-Kadi, A.; Roy, C. - Adv. Polym. Techn., 17, 127 (1998).

23. Van der Wal, A.; Nijhof, R.; Gaymans, R. J. - Polymer, 40, 6031 (1999).

24. Willemse, R. C.; Speijer, A.; Langeraar, A. E.; Posthuma, B. - Polymer, 40, 6645 (1999).

25. Flaris, V.; Stachursky, Z. N. - J. Appl. Polym. Sci., 45, 1789 (1992).

26. Willemse, R. C.; Ramaker, E. J. J.; Van Dam, J.; Boer, A. P. - Polym . Eng. Sci., 40, 6651 (1999).

27. Willemse, R. C. - Polymer, 40, 2175 (1999).

28. Guimarães, M. J. O. C.; Rocha, M. C. G.; Coutinho, F. M. B.; Farah, M.; Bretas, R. E. S. - J. Appl. Polym. Sci., 2002 (em publicação).



588370e77f8c9d0a0c8b461d polimeros Articles
Links & Downloads

Polímeros: Ciência e Tecnologia

Share this page
Page Sections